CompTIA 220-702 Exam question and answer

220-702 Exam CompTIA A+ Practical Application (2009 Edition)
Exam Number/Code : 220-702
Exam Name : CompTIA A+ Practical Application (2009 Edition)
Questions and Answers : 610 Q&As

CompTIA 220-702 exam information
CompTIA 220-702 exam consists of multiple-choice questions. There are no case study type questions and the test is not adaptive. You will be required to attempt approximately 100 questions in 90 minutes. To pass, you need a score of 700 on a scale of 100-900.

CompTIA 220-702 exam description
CompTIA’s 220-702 exam is designed to measure your ability to support computers and install, configure, troubleshoot, optimize, diagnose and perform preventive maintenance in the field or in organizations. CompTIA A+ Practical Application (220-702) is an extension of the knowledge and skills identified in CompTIA A+ Essentials, with more of a “hands-on” orientation focused on scenarios in which troubleshooting and tools must be applied to resolve problems. You now have to pass both 220-701 and 220-702 exams to achieve the new A+ certification. The CompTIA A+ certification is the industry standard for computer support technicians. This is the international, vendor-neutral certification that proves competence in areas such as installation, preventative maintenance, networking, security, and troubleshooting. CompTIA A+ certified technicians have excellent customer service and communication skills to work with clients. The A+ certification demonstrates competency as a computer technician.

Before taking the CompTIA 220-702 exam , a candidate should practice the following
1.Add, remove, configure, and maintain computer components.
2.Detect problems, troubleshoot and repair/replace personal computer components.
3.Install, configure, detect problems, troubleshoot and repair/replace laptop components

CompTIA 220-702 exam demo for share

1. A customer reports they are unable to connect to any computers outside of the office and they are unable
to connect to the Internet. When the technician runs ipconfig, the customer gets the following output:
IP address169.254.2.4
Subnet Mask.255.255.0.0
Default Gateway.
Which of the following could be causing the issue?
A. The subnet mask is not correctly configured.
B. The DNS client has not been configured on the computer.
C. The DHCP client is unable to obtain an IP address from the DHCP server.
D. The default gateway is not specified.
Answer: C
2. A user reports that their system is starting to run slower, especially when opening large local files. The
system has sufficient RAM for the users applications, but the hard drive seems to have higher than normal
activity when opening large files. Which of the following would be the BEST tool to diagnose and
troubleshoot this problem?
A. Task Manager
B. NTBACKUP
C. FDISK
D. Disk Defragmenter
Answer: D
3. A user states they receive a message Boot device not found half of the time they boot their system.
Which of the following is the MOST likely cause?
A. A dead CMOS battery
B. The OS is not installed on the hard drive
C. A faulty RAM
D. A faulty HDD connection
Answer: D
4. A technician needs to check which ports are open in the Windows Firewall. Which of the following will
allow the technician to view these settings?
A. netsh firewall show logging
B. ipconfig /all
C. netsh firewall show state
D. arp -a
Answer: C
5. A remote user is attempting to install a new external storage device on their computer. The user reports
they only have one port open on the back of the device and the port is similar to the USB port their mouse is
connected to. The port has a bevel on one side and is slightly larger than the USB port. Which of the
following connector types is MOST likely being described?
A. IEEE 1394
B. USB 2.0
C. PCMCIA
D. Parallel
Answer: A
6. A Windows XP system locks up after the GUI starts to load. The system will start in Safe Mode. The
Event Viewer reports that a driver failed to load. Which of the following methods would help diagnose the
problem?
A. Enable boot logging. In Safe Mode, read the ntbtlog.txt file.
B. In Safe Mode, run the sigverif utility.
C. Restart the system from the OEM recovery CD; do a full restore.
D. In Safe Mode, run the driverquery utility.
Answer: A
7. After a technician installs a new CMOS battery on a motherboard, which of the following will the
technician have to change?
A. Firmware version
B. System date/time
C. Bus speeds
D. Jumper settings
Answer: B
8. A technician has just installed an upgraded graphics card. The computers power turns off before it
finishes booting. Which of the following is the cause of the problem?
A. The monitor cannot display the increased resolution that is a feature of the new graphics card.
B. The power supply does not provide enough wattage to power the new graphics card.
C. The new graphics card is incompatible with the existing processor.
D. The computer does not have enough RAM to support the new graphics card.
Answer: B
9. A technician notices that the BIOS event log shows a chassis intrusion. Which of the following is the
MOST likely reason for the event?
A. There is a loose object in the case.
B. An optical drive drawer is open.
C. The computer case was opened.
D. An attacker hacked into the system.
Answer: C
10. If a technician is traveling outside of the US, which of the following should be checked before setting up
a workstation?
A. Local file format
B. Wattage setting
C. Local power codes
D. Voltage setting
Answer: D

www.test4pass.com